Length:
415 mm (16.4 in.)
Width:
293 mm (11.6 in.)
Height:
444 mm (17.5 in.)
Weight:
17.5 kg (38.6 lbs.)
All figures include mounting yoke
Color wheel:
8 interchangeable colors + open
Gobo wheel:
6 rotating gobos plus open, indexing, variable rotation
Gobo animation:
Variable speed linear animation effect
Prism:
Prism wheel with 2 interchangeable prisms, prism rotation and indexing
Frost (wash effect):
Motorized variable
Dimming:
Electronic, constantly variable 0-100%, 16-bit control
Shutter:
Strobe and pulse effects, instant open and blackout
Focus:
Motorized, variable 3 m (9.8 ft.) to infinity
Stand-alone control:
Up to 20 scenes with global fade/hold times
DMX channels:
13
DMX compliance:
USITT DMX512-A
RDM compliance:
ANSI/ESTA E1.20
Control options:
DMX, RDM, standalone
Configuration, addressing and status:
Onboard control panel with OLED display
8-bit control:
color/gobo selection, prism, frost, animation
16-bit control:
Gobo indexing and rotation, focus and intensity
Light source:
230 W white light LED engine
CRI (Color Rendering Index):
72
Color temperature:
8300 K
LED lifetime:
20,000 hours (to >70% luminous output)*
LED manufacturer:
Prolight Opto
Binning:
Tight color and flux binning
*Figure obtained under manufacturer's test conditions
Narrow:
Cut-off angle: 12°
Total output: 5000 lumens
Center peak: 203,000 cd
Medium:
Cut-off angle: 22°
Total output: 6100 lumens
Center peak: 77,000 cd
Wide:
Cut-off angle: 37°
Total output: 5700 lumens
Center peak: 28,000 cd
Very Wide:
Cut-off angle: 50°
Total output: 3400 lumens
Center peak: 11,000 cd
* All Photometric Data measured in steady state (30 minutes warm-up time) at 25°C ambient.
Housing:
Cast aluminum
Finish:
Hard anodized, metallic grey lacquered
Front glass:
5 mm (0.2 in.) anti-reflection coated tempered glass
Ingress protection:
IP66
Impact resistance:
IK08 (with control panel display cover plate installed)
Corrosion resistance:
C5-M (very high corrosivity / marine, ISO 12944)
Vibration resistance:
1.0g, Sinusoidal (IEC 60068-2-6)
0,7g RMS Random (IEC 60068-2-64)
EPA (Effective Projected Area):
0.15 m2
RoHS compliant
Suitable material:
Borosilicate glass, coatings heat-resistant to 450°C (842° F)
Alternative material:
Aluminum 1060, paint on front lens side, 450° C (842° F)
Gobo diameter:
30.0 mm +0/-0.3 mm (1.2 in. +0/-0.02 in.)
Maximum image diameter:
23 mm (0.91 in.)
Glass gobo thickness, minimum:
1.1 mm ±0.1 mm (0.045 ±0.004 in.)
Glass gobo thickness, maximum:
3.0 mm ±0.3 mm (0.12in. ± 0.012 in.)
Aluminum gobo thickness:
0.5 mm ± 0.02 mm (0.020 in. ± 001 in.)
HT paint
Mounting:
Adjustable yoke
Location:
Suitable for wet locations. Do not immerse in water.
Orientation:
Any (sides must be kept vertical)
Minimum distance to illuminated surfaces:
0.5 m (20 in.)
Power cable entry:
IP68 cable gland
Power connection:
1.8 m (5.9 ft.) cable tail with bare ends
Data cable entry:
IP68 cable gland
Data connection:
1.8 m (5.9 ft.) combined input + output cable tail with bare ends
AC power:
100-240/277 V nominal, 50/60 Hz
Power Supply:
Auto-ranging electronic switch-mode
Typical half-cycle RMS inrush current:
8.4 A
Idle power (zero intensity, no effects applied):
32 W, 0.3 A
Surge protection:
4 KV
110 V, 60 Hz:
320 W, 2.9 A, PF 0.977
230 V, 50 Hz:
310 W, 1.4 A, PF 0.971
277 V, 60 Hz:
305 W, 1.2 A, PF 0.950
Figures are typical, not maximum. Measurements made at nominal voltage with all LEDs at full intensity. Allow for a deviation of +/- 10%.
Cooling:
Convection, internal forced air
Total heat dissipation (calculated):
1100 BTU/hr.
Maximum surface temperature:
85° C (185° F)
Maximum ambient temperature (Ta max.):
45° C (113° F) *
Minimum ambient temperature (Ta min.):
-30° C (-22° F)**
*Above this temperature, the fixture regulates output to protect from overheating.
** An integrated heat-element will heat-up internal components at ambient temperatures below 0° C (32° F) - For instant wake-up with no warm-up time, leave power applied constantly.
RoHS:
Compliant
REACH:
Compliant
WEEE:
Compliant
Proposition 65:
Compliant
Efficacy (max output):
20 lm/W
LWR*:
349 lm/kg (158 lm/lb)
LWR = Lumen-to-Weight Ratio
Global CB Certification/IECEE:
IEC 60598-2-5 (IEC 60598-1)
EU safety:
EN 60598-2-1, EN 60598-2-5 (EN 60598-1), EN 62471, EN 62493
EU EMC:
EN 55015, EN 55032, EN 55103-2, EN 61000-3-2, EN 61000-3-3, EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61547
US safety:
ANSI/UL 1598
US EMC:
CFR 47 Part 15 Class A
Canadian safety:
CSA C22.2 No 250.0
Australia/NZ:
RCM
India:
BIS
Martin Companion Cable:
P/N 91616091
Martin Companion Software Suite (including firmware uploader)
Glare Shield, Exterior Projection 500, aluminum:
P/N 91611767
Projection Setup Gobo:
P/N 91616068
EP-500, Manual Framing Module:
P/N 91611842
Ring for gobo, OD30, set of 10 pcs:
P/N MAR-91611851
Silica gel desiccant bag in sealed foil pack:
P/N 37220000
Goboholder with magnet incl. washer, short spring & long spring:
P/N 50481990
Goboholder without magnet incl. washer, short spring & long spring:
P/N 50481992
EU models:
Exterior Projection 500, Narrow, EU, Aluminum: P/N 90506500
Exterior Projection 500, Medium, EU, Aluminum: P/N 90506505
Exterior Projection 500, Wide, EU, Aluminum: P/N 90506510
Exterior Projection 500, Very Wide, EU, Aluminum: P/N 90506535
Exterior Projection 500, Narrow, EU, White: P/N 90506540
Exterior Projection 500, Medium, EU, White: P/N 90506545
Exterior Projection 500, Wide, EU, White: P/N 90506550
Exterior Projection 500, Very Wide, EU, White: P/N 90506555
US Models:
Exterior Projection 500, Narrow, US, Aluminum: P/N 90506515
Exterior Projection 500, Medium, US, Aluminum: P/N 90506520
Exterior Projection 500, Wide, US, Aluminum: P/N 90506525
Exterior Projection 500, Very Wide, US, Aluminum: P/N 90506530
version A,
updated: Oct 2020
Dealer Finder
Have a Question?
Consultant Support
